EPOXY GARAGE FLOORS MISSOURI
Your Garage Deserves a Floor Built to Last.
Surface Solutions installs professional-grade epoxy garage floors for homeowners across Missouri. Whether you're finishing a new garage or replacing a floor that's peeling, staining, or cracking, we apply a system built to handle vehicle traffic, chemical spills, hard winters, and decades of daily use. One standard on every job: do it right the first time.
What Goes Into an Epoxy Garage Floor
STEP 1: SURFACE PREPARATION
​​
We diamond grind every surface to open the concrete profile and ensure maximum adhesion. Cracks are filled with a professional polyurea filler that bonds directly into the concrete. Every slab is moisture-tested before anything goes down — because a properly prepared surface is what the entire system depends on.
-
Diamond grinding to open the concrete surface profile for maximum bond
-
Professional polyurea crack filler, not surface caulk
-
Moisture vapor testing on every slab before coating
-
Moisture vapor barrier primer applied when the slab requires it
STEP 2: 100% SOLIDS EPOXY BASECOAT
​
Our basecoat is a 100% solids, USA-made epoxy formula — no water, no solvents, no fillers. Every ounce of product goes directly into building film thickness and bond strength on your floor. This is the foundation the rest of the system sits on.
-
100% solids formula with no fillers, no water content, and no shrinkage after cure
-
Manufactured in the USA to professional-grade quality standards
-
Builds maximum film thickness and compressive strength
-
Bonds directly to properly prepared concrete for long-term adhesion
STEP 3: DECORATIVE COLOR CHIP BROADCAST
​
Once the basecoat is applied, we broadcast decorative vinyl color chip flake across the full surface while the epoxy is still wet. The chips become part of the coating — adding texture, slip resistance, and a finished look that holds up under traffic without showing wear patterns.
-
Full broadcast coverage for a consistent, finished look
-
Chips pressed into the basecoat and sealed in, not sitting on the surface
-
Adds natural slip resistance underfoot
-
Available in a range of standard color blends and custom combinations
-
Conceals minor surface imperfections in the concrete
STEP 4: POLYASPARTIC TOPCOAT
​
Every epoxy garage floor we install is finished with a high-performance polyaspartic topcoat. UV stable, chemical resistant, and built to hold up under vehicle traffic and Missouri winters — this is what gives the floor its lasting durability and sharp appearance year after year.
-
UV stable — won't yellow or chalk in sunlight or near garage door openings
-
Resists hot tire pickup — a common failure point in consumer-grade systems
-
Chemical resistant against oil, road salt, deicer, and automotive fluids
-
High abrasion resistance for vehicle traffic and heavy foot traffic
-
Available in gloss and satin finishes
​Why Missouri Homeowners Choose Surface Solutions
USA-MADE EPOXY, FLAKE & ASPARTIC SYSTEMS
​
Every product we use in our epoxy garage floor system is manufactured in the United States to professional-grade quality standards. Our 100% solids formulas contain no water, no solvents, and no fillers. What goes in the can goes on your floor, building the film thickness and bond strength that makes the difference between a coating that performs for decades and one that doesn't.
WE DON'T SKIP THE PREP
​
The prep is where most coatings fail and where corners are often cut. We diamond grind every surface, fill every crack with professional polyurea filler, and test every slab for moisture before anything goes down. There are no shortcuts in our process, regardless of the size of the job or the schedule we're working with.
YOU GET THE OWNER ON EVERY JOB
​
Surface Solutions is owner-operated. The owner shows up for the estimate, the prep, the application, and the final walk-through on every job we take on. That means consistent standards, direct communication, and someone with a personal stake in the quality of your floor from start to finish.
STRAIGHT ANSWERS, NO PRESSURE
​
We give honest assessments on every garage floor we look at across Missouri. If your concrete has a moisture problem that needs to be addressed before coating, we'll tell you. If a simpler system will do the job just as well, we'll tell you that too. No inflated scopes, no pressure tactics, no surprises on job day.
FREE ON-SITE ESTIMATE
​
We walk every garage before we quote it. That means we see the actual condition of the concrete, identify any issues that need to be addressed, and give you a number based on what the job actually requires. No estimates over the phone, no surprises when we show up.
What Makes a Professional Garage Installation Different
If you've been researching epoxy garage floors, you've probably come across a wide range of options, from home improvement store kits to local contractors at a range of price points. Here's what actually separates a floor that holds for 15 to 20 years from one that starts peeling in two or three.
IT STARTS WITH THE PRODUCT​
​
Professional-grade 100% solids epoxy systems are fundamentally different from the water-based or low-solids formulas sold in consumer kits. In a 100% solids formula, every ounce of product bonds directly to your concrete, building real film thickness and strength. Water-based formulas shrink as they cure, leaving a thinner, weaker coating that bonds to the surface rather than into it.
THEN IT COMES DOWN TO PREP​
​
No coating, regardless of quality, holds long-term over unprepared concrete. Diamond grinding opens the surface so the coating can bond properly. Moisture testing protects the coating from vapor pressure building beneath it. Polyurea crack filling stabilizes the slab before the system goes down. Each step matters, and each one takes time and equipment. That's why they're easy to skip, and why skipping them is the most common reason garage floors fail.
APPLICATION IS THE FINAL VARIABLE
​
Professional-grade products require professional mixing ratios, proper temperature conditions, and application techniques that consumer kits aren't designed for. When you hire Surface Solutions, you're getting the right product applied the right way on a properly prepared surface, with a result that will still look sharp years from now.
Common Questions
About Epoxy Garage Floors
HOW LONG DOES AN EPOXY GARAGE FLOOR LAST?
A properly installed 100% solids epoxy system with a polyaspartic topcoat will last 15 to 20 years or more under normal residential garage use. The prep work is the biggest factor in longevity. A floor installed over a properly ground, moisture-tested slab with professional-grade products will significantly outlast anything installed over unprepped concrete with consumer-grade materials.
HOW LONG DOES INSTALLATION TAKE?
Most residential garage floors are completed in one to two days. The first day covers surface preparation and the epoxy basecoat. The chip broadcast and polyaspartic topcoat go down after the basecoat has cured. We'll give you a specific timeline during your estimate based on the size of your garage and the condition of the concrete.
HOW SOON CAN I USE MY GARAGE AFTER INSTALLATION?
Light foot traffic is typically safe within 24 hours. Vehicle traffic generally requires 48 to 72 hours depending on temperature and humidity conditions during the cure. We'll give you specific return-to-service times based on the products and conditions on your job.
CAN EPOXY BE APPLIED OVER MY EXISTING GARAGE FLOOR?
In most cases, yes. The condition of the existing concrete determines the scope of prep work required. Existing paint or previous coatings need to be ground off before a new system can be applied. Significant cracking, spalling, or moisture issues need to be addressed before coating. We assess all of this during the free on-site estimate so you know exactly what the job involves before committing to anything.
DO YOU OFFER COLOR CHOICES?
Yes. We offer a range of standard color chip blends and can work with custom combinations to match your preference. We'll bring samples to the estimate so you can see the options against your actual concrete and garage environment before making a decision.